routesink3

How to Replace a Kia Sportage Replacement Key For a number of Kia models, the key contains the keyless entry system that is built into the key. This key usually resembles the remote control and is able to be replaced with a new one from a Kia dealer or locksmith. Key fobs can stop working due to a number of reasons, such as a dead battery, worn-out buttons signals, signal interference or water damage. Here are some suggestions on how to get your Kia Sportage replacement key to work again. How to replace the remote key or smart key It doesn't matter if your Kia comes with an intelligent key, remote key, push-to-start keys, or regular metal non-transponder key the battery in these keys will eventually require replacing. replacement kia key fob is especially the case if your car displays a message that indicates the smart or remote keys aren't powered. Luckily, this is an easy procedure. In order to replace the key fob battery take the mechanical key from the slit on the back of the key fob. You then need to lift the cover. A small screw will be located inside the key fob that holds the battery in the correct position. By using a small screwdriver loosen the screw and remove the old battery. Insert the new battery and close the slit on the key fob. Test the key fob by pressing the lock or unlock buttons. You're in good shape in case the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or when you need to do some errands in Brandon. Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non transponder keys made of steel), do not need programming. If your key requires to be programmed again, you must know the key code number stamped on the key code tag and keep it in a safe place. How do you replace a battery? If the Kia key fob doesn't respond when you press the lock/unlock button, it is likely that the battery is depleted. A battery that is not functioning properly could cause other issues such as the check engine light turning on or a delay in cranking the engine. Fortunately, replacing the key fob battery is a relatively easy DIY project that requires only the most basic tools. Make sure that you shut off your vehicle and shut the doors before you begin. Find the small, metal or plastic piece near the bottom of the key fob. Jiggle it until the key comes out. You can then insert the key in the handle on the door of your driver to open your car. To replace the battery in the key fob, remove the rear cover. Use a plastic pry tool to open the latch that holds the black negative cable. Remove the old battery, and then align the new battery to ensure that the “+” positive side is facing you, and the “negative” negative side is facing the fob's metal electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts. Once the new battery has been installed then turn the key fob off and then turn it on in the ignition repeatedly until the door locks. You can then test the Kia's Key fob once more to ensure it's working as intended. How to replace a smart key Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The smart key is equipped with an embedded mechanical key blade however, the standard key fob does not. Both key fobs have a battery that will eventually need to be changed. This is an easy process that takes less than two minutes. Be sure to turn off your Kia and stand on a level or well-lit surface prior to when you begin. Keep in mind that there are tiny pieces inside the fob which could fall out if you are not vigilant. The first step is to find the small release button on the back of the lower part of the fob. It will be either an oval silver button or a rectangular slot. You can open the key fob by pressing the button. Once you have the key fob opened and you are able to take out the old battery and replace it. The new battery is the CR-2032, and it can be bought from a local or online auto parts store. Once you're done, you should be able to lock, unlock and start your car using your key fob, even if your engine isn't running! How to replace the mechanical key? The Kia key fob is a great feature that lets us lock and unlock our car with the click of one button. As with all devices, the Kia key fob may have issues. There are solutions to address these issues and keep your key fobs functioning for many years. A dead or drained battery is among the most common issues. This can cause the fob to cease working or work intermittently. If this is the case you should replace the battery a new one. If this isn't enough to resolve the issue Try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to scratch any internal components or scratch the plastic. After the battery has been removed, replace it with a brand new one. When the new battery is in, close and open the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that will fit into the slot). Test the key fob and make sure it is working correctly. Contact a dealer, or a locksmith to address the issue in the event that the key fob is not working. Make sure they cut you an emergency key that can work across all trunk and door cylinders, to prevent lockouts in the future.